5mm Bi - Color Hyper Indicator LED 100 MW With AlGaInP Material , ROHS Standard

DL-509SRYGCA-A.pdf

Feature

product model : DL-509SRGMA-A

Material:AlGaInP

Peak Forward Current:100mA

(1/10 Duty.Cycle.0.1ms Pulse width)

Continuous Forward Current:35mA

Derating Linear From 50°C :0.4mA/ °C

Reverse Voltage:5V

Operating Temperature Range:-40°C to +80°C

Storage Temperature Range :-40°C to +80°C

Lead Soldering Temperature:260°C for 5 Seconds

1. Size: 3mm, 5mm, 8mm.10mm,12mm 0603, 1210/3528, 5050

2. Shapes: round, burgonet, straw cap, Super Flux, SMD, High Power

3. Emitting color: red, yellow, blue, green, white, warm white,full color,RGB flash

4. Beam Angle: 15,20, 30, 45, 60, 80, 120 degrees

5. Wave length:(different wave length available)

6. Forward Voltage: 2.0-2.4V for red, yellow color, 3.0-3.6V for white .blue, green, white

7. Forward Current: 15~20mA, 350mA,700mA

8. Lens colors: water clear, color diffused

9. Certification:CE/ROHS/ISO9001:2000 Approved

10. Luminous Intensity: (different available)

11. Packing: 1000Pcs/antistatic bag,

Application

1Indoor and outdoor commercial lighting

2. Architectural Lighting

3. General lighting

4. Automotive lights

5. Mood Lighting, LED module

6. Traffic Light

7. LCD TV / monitor backlights

8. LED display

9. Reading light, LED torch

10. Craft flashlights, headlights

•  
•  
•  
•  
•  
•  
•  
• Package Dimension:

Absolute Maximum Ratings at Ta=25℃

• Notes:

• All dimensions are in millimeters (inches).
• Tolerance is ± 0.25 mm (.010″) unless otherwise noted.
• Protruded resin under flange is 1.00 mm (.04″) max.
• Specifications are subject to change without notice.

​

• Reliability Test Items And Conditions:

The reliability of products shall be satisfied with items listed below:

Confidence level: 90%. LTPD: 10%.

• Test Items and Results:

• Criteria For Judging The Damage:

• Please read the following notes before using the product:

• Over-current-proof

Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen).

• Storage

1.1 Do not open moisture proof bag before the products are ready to use.

1.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

1.3 The LEDs should be used within a year.

1.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.

1.5 The LEDs should be used within 168 hours (7 days) after opening the package.

• Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.

• Repairing

Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.

• Caution in ESD

Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices equipment and machinery must be properly grounded.