Product Details:
Payment & Shipping Terms:
|
Product Name: | 3mm Cylindrical With Flange Lamp LED | Package: | Standard T-1 3/4 Diameter Package |
---|---|---|---|
Emitted Color: | Infrared | Product Number: | DL-304IRCX-1IR80 |
Lens Type: | Water Clear | Forward Voltage @20ma: | 0.8-1.8V |
Viewing Angle: | 80Deg | Forward Current: | 100mA |
Peak Emission Wavelength: | 940nm | Spectral Bandwidth: | 50nm |
High Light: | ir emitting diode,940nm infrared led |
Know more details,please contact with me to get specifications.
Part No. | Chip Material | Lens Color | Source Color |
DL-304IRCX-1IR80 | GaAlAs | Water Clear | Infrared |
Notes:
Parameters | Symbol | Min. | Typ. | Max. | Unit | Test Condition |
Radiant Intensity | IV | 18.0 | 24.0 | --- | mW/sr | IF=20mA |
Ee | --- | 42.0 | --- | IF=100mA, tp=100µs, tp/T=0.01 | ||
Viewing Angle | 2θ1/2 | --- | 80 | --- | Deg | IF=20mA (Note 2) |
Peak Emission Wavelength | λp | --- | 940 | --- | nm | IF=20mA |
Spectral Bandwidth | Δλ | --- | 50 | --- | nm | IF=20mA |
Forward Voltage | VF | 0.80 | 1.20 | 1.50 | V | IF=20mA |
VF | --- | 1.60 | 1.80 | V | IF=100mA, tp=100µs, tp/T=0.01 | |
Reverse Current | IR | --- | --- | 10 | µA | VR=5V |
Notes:
. Manual of Soldering
1.The temperature of the iron tip should not be higher than 300℃ (572℉) and Soldering within 3 seconds per solder-land is to be observed.
2. Reflow Soldering
Preheating: 140℃~160℃±5℃, within 2 minutes.
Operation heating: 235℃ (Max.) within 10 seconds (Max)
Gradual Cooling (Avoid quenching).
3. DIP soldering (Wave Soldering):
Preheating: 120℃~150℃, within 120~180 sec.
Operation heating: 245℃±5℃ within 5 sec.260℃ (Max)
Gradual Cooling (Avoid quenching).
Care must be taken not to cause to the epoxy resin portion of LEDs while it is exposed to high temperature.
Care must be taken not rub the epoxy resin portion of LEDs with hard or sharp article such as the sand blast and the metal hook.
Care must be taken to provide the current limiting resistor in the circuit so as to drive the LEDs within the rated figures. Also, caution should be taken not to overload LEDs with instantaneous voltage at the turning ON and OFF of the circuit.
When using the pulse drive care must be taken to keep the average current within the rated figures. Also, the circuit should be designed so as be subjected to reverse voltage when turning off the LEDs.
In order to avoid the absorption of moisture, it is recommended to solder LEDs as soon as possible after unpacking the sealed envelope.
If the envelope is still packed, to store it in the environment as following:
1.Temperature : 5℃-30℃ (41℉), Humidity : RH 60﹪Max.
2.After this bag is opened, devices that will be applied to infrared reflow, vapor-phase reflow, or equivalent soldering process must be:
a)Completed within 24 hours.
b)Stored at less than 30% RH.
3.Devices require baking before mounting, if (2) a or (2) b is not met.
4.If baking is required, devices must be baked under below conditions: 12 hours at 60℃±3℃.
Products are packed in one bag of 500pcs (one taping reel) and a label is attached on each bag.
HongKong Double Light Electronics was founded in 2005 as a professional LED manufacturer located in Shenzhen, China. We mainly produce a wide range of products with automatic production lines, which include THT LEDs, chip LEDs, LED displays, infrared LEDs, dot matrix, LCD backlights and LED lighting fixtures.
Contact Person: Mr. Rony Qiu
Tel: 86-755-82853859
Fax: 86-755-83229774