|
Product Details:
Payment & Shipping Terms:
|
Product Name: | 3mm Round Standard T-1 Type | Source Color: | Ultra Yellow |
---|---|---|---|
Forward Voltage @20ma: | 2.20V | Viewing Angle: | 30Deg |
Forward Current: | 25mA | Peak Emission Wavelength: | 592nm |
Power Dissipation: | 75mW | ||
High Light: | 592nm Led Light Chip,30Deg Led Light Chip,25mA High Power Led Chip |
3mm Round Standard T-1 Type Ultra Yellow LED led light components
Features:
1. Choice of various color.
2. Available on tape and reel.
3. Reliable and robust.
4. The product itself will remain within RoHS compliant Version.
Descriptions:
1. The series is specially designed for applications requiring higher brightness.
2. The LED lamps are available with different colors, intensities.
Applications:
1. Status indicators.
2. Commercial use.
3. Advertising Signs.
4. Back lighting.
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ± 0.25 mm (.010″) unless otherwise noted.
3. Protruded resin under flange is 1.00 mm (.039″) max.
4. Specifications are subject to change without notice.
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ± 0.25 mm (.010″) unless otherwise noted.
3. Protruded resin under flange is 1.00 mm (.039″) max.
4. Specifications are subject to change without notice.
Absolute Maximum Ratings at Ta=25
Parameters | Symbol | Max. | Unit |
Power Dissipation | PD | 75 | mW |
Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) |
IFP | 100 | mA |
Forward Current | IF | 25 | mA |
Reverse Voltage | VR | 5 | V |
Operating Temperature Range | Topr | -40℃ to +85℃ | |
Storage Temperature Range | Tstg | -40℃ to +100℃ | |
Lead Soldering Temperature [4mm (.157″) From Body] |
Tsld | 260℃ for 5 Seconds |
Electrical Optical Characteristics at Ta=25℃
Parameters | Symbol | Min. | Typ. | Max. | Unit | Test Condition |
Luminous Intensity * | IV | 185 | 320 | --- | mcd | IF=20mA (Note 1) |
Viewing Angle * | 2θ1/2 | --- | 30 | --- | Deg | IF=20mA (Note 2) |
Peak Emission Wavelength | λp | --- | 592 | --- | nm | IF=20mA |
Dominant Wavelength | λd | --- | 589 | --- | nm | IF=20mA (Note 3) |
Spectral Line Half-Width | △λ | --- | 15 | --- | nm | I F =20mA |
Forward Voltage | VF | 1.80 | 2.20 | 2.60 | V | IF=20mA |
Reverse Current | IR | --- | --- | 10 | µA | VR=5V |
Notes:
1. Luminous Intensity Measurement allowance is ± 10%.
2. θ 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
3. The dominant wavelength (λd) is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device.
Please read the following notes before using the product:
1. Over-current-proof
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.
2. Repairing
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90% RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70% RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
3. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.
4. Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
Company Introduction
HongKong Double Light Electronics Technology Co. Ltd was founded in 2005 as a professional LED manufacturer located in Shenzhen, China. We mainly produce a wide range of products with automatic production lines, which include THT LEDs, chip LEDs, LED displays, infrared LEDs, dot matrix, LCD backlights and LED lighting fixtures.
Contact Person: Mr. Chen
Tel: 86-755-82853859
Fax: 86-755-83229774