Payment & Shipping Terms:
|Product Name:||1W High Power Yellow LED||Package:||1W High Power LED With Lens|
|Emitted Color:||Yellow Color||Peak Emission Wavelength:||589nm|
|Lens Type:||Water Clear||Forward Voltage @20ma:||2.0-3.0V|
|Luminous Intensity:||40-60LM||Viewing Angle:||60 Deg|
light emitted diode,
light emission diode
This is our 1W High Power Yellow LED, its lens color is water clear and emitting color is yellow color.
|Part No.||Chip Material||Lens Color||Source Color|
|DL-HP10UYC-1W60||AlGaInP||Water clear||Ultra Yellow|
Absolute Maximum Ratings at Ta=25℃
|PeakPulseCurrent (tp≤100μs, Duty cycle=0.25)||I pulse||700||mA|
|LED Junction Temperature||Tj||125||℃|
|Operating Temperature Range||Topr||-40 to +80||℃|
|Storage Temperature Range||Tstg||-40 to +100||℃|
|Soldering Time at 260 ℃ (Max.)||Tsol||5||Seconds|
Electrical Optical Characteristics at Ta=25℃
|Viewing Angle ||2θ1/2||---||60||--||Deg||IF=500mA|
|Forward Voltage ||VF||2.0||2.30||3.00||V||IF=500mA|
|Peak Emission Wavelength||λp||---||592||---||nm||IF=500mA|
|Dominant Wavelength||λd||---||589||---||nm||IF =500mA|
|Spectrum Radiation Bandwidth||Δλ||---||15||---||nm||IF=500mA|
1. 2θ1/2 is the off axis angle from lamp centerline where the luminous intensity is 1/2 of the peak value. 2. Forward Voltage measurement tolerance: ±0.1V
Typical Electrical / Optical Characteristics Curves
(25℃ Ambient Temperature Unless Otherwise Noted)
Relative Spectral Distribution
Forward Current VS Forward Voltage
Forward Current (mA)
Maximum Current(mA) VS Ambient
Typical Spatial Radiation Pattern
Please read the following notes before using the product:
Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen).
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture adsorbent material (silica gel) has fabled away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment: 60±5℃ for 24 hours.
3.1 Pb-free solder temperature profile.
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded.
Contact Person: Tanky