Payment & Shipping Terms:
|Product Name:||Infrared LEDs||Diameter:||1206 Size|
|Emitted Color:||940nm Infrared LED||Peak Emission Wavelength:||940nm|
|Chip Material:||Silicon||Lens Type:||Black|
|Forward Voltage @20ma:||1.1-1.4V||Viewing Angle:||30 Deg|
light emitting diode led,
ir emitting diode
1206 Silicon Phototransistor 940nm Infrared Emitting Diode 30 Deg Reception Angle SMD LED diode
1. Fast response time.
2. Outline Package:3.2x1.6x2.33mm
3. High photo sensitivity.
4. Small junction capacitance.
5. Package in 8mm tape on 7” diameter reel.
6. The product itself will remain within RoHS compliant Version.
1. The 1206 SMD LED is a high speed and high sensitive silicon NPN phototransistor in miniature SMD package which is molded in a black epoxy with flat top view lens.
2. Due to its black epoxy, the device is spectrally matched to visible and infrared emitting diode.
1. Automatic door sensor.
2. Infrared applied system.
3. Counters and sorters.
5. Floppy disk drive.
6. Optoelectronic switch.
7. Video camera, tape and card readers.
8. Position sensors.
10. Game machine.
11. Applicable to all kinds of mechanical keyboard launch requirements
12. Suitable for all kinds of infrared transmitting and receiving equipment
13. Infrared remote control transmitter is suitable for all kinds of electronic products
14. Applicable to all kinds of small household electrical appliance products for reflection application
|Part No.||Chip Material||Lens Color||Source Color|
Absolute Maximum Ratings at Ta=25℃
|Operating Temperature Range||Topr||-40℃ to +80℃|
|Storage Temperature Range||Tstg||-40℃ to +85℃|
|Lead Soldering Temperature||Tsld||260℃ for 5 Seconds|
Electrical Optical Characteristics at Ta=25℃
|Collector-Emitter Breakdown Voltage||BVCEO||30||---||---||V||IC=100μA,|
|Emitter-Collector Breakdown Voltage||BVECO||5||---||---||V||IE=100μA,|
|Viewing Angle *||2θ 1/2||---||30||---||Deg|
|Peak Emission Wavelength||λp||---||940||---||nm|
|Rang Of Spectral Bandwidth||λ0.5||700||---||1200||nm|
Please read the following notes before using the product:
Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen).
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture adsorbent material (silica gel) has fabled away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment: 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile.
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
6. Caution in ESD
Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded.
HongKong Double Light Electronics was founded in 2005 as a professional LED manufacturer located in Shenzhen, China. We mainly produce a wide range of products with automatic production lines, which include THT LEDs, chip LEDs, LED displays, infrared emitting diode LEDs, dot matrix, LCD backlights and LED lighting fixtures.
Other hot sell products
Buy infrared emitting diode LEDs, come DOUBLE LIGHT.
Contact Person: Tanky