Payment & Shipping Terms:
|Product Name:||0.55mm Height PLCC-2 Package Top View 3030 LED Grow Lights Components||Package:||Top View Chip LED 3030|
|Emitted Color:||Red||Product Number:||DL-TOP3030GL-R|
|Color Temperature:||605-625nm||Forward Voltage:||3.0-3.6V|
|Forward Current:||350mA||Luminous Flux:||10-16lm|
|Viewing Angle:||120 Deg|
led smd rgb,
brightest smd led
PLCC -2 Package Top View 3030 SMD Chip LED Grow Lights Components Color Changeable
This is our 0.55mm Height PLCC-2 Package Top View 3030 LED grow lights components, the TOP2835 series is available in soft red, orange, yellow, green, blue and white. The LED has wide viewing angle and optimized light coupling by inter reflector. This feature makes the SMT TOP LED ideal for light pipe application. The low current requirement makes this device ideal for portable equipment or any other application where power is at a premium.
Our led grow light mainly are red and blue spectrum, these two spectrums are the peak of plants absorption.
|Part No.||Chip Material||Lens Color||Source Color|
|DL-TOP3030GL-R||AlGaInP||Pink Diffused||Hyper Red|
Specifications are subject to change without notice.
Absolute Maximum Ratings at Ta=25℃
Peak Forward Current
(1/10 Duty Cycle, 0.1ms Pulse Width)
|Electrostatic Discharge (HBM)||ESD||2000||V|
|Operating Temperature Range||Topr||-40℃ to +80℃|
|Storage Temperature Range||Tstg||-40℃ to +85℃|
|Soldering Temperature||Tsld||260℃ for 5 Seconds|
Electrical Optical Characteristics at Ta=25℃
|Peak Emission Wavelength||λp||-516||-506||-496||nm||IF=350mA|
The reliability of products shall be satisfied with items listed below:
Confidence level: 90%.
1) Test Items and Results:
|No.||Test Item||Test Hours/Cycles||Test Conditions||Sample Size||Ac/Re|
|1||Resistance to Soldering Heat||6 Min||
|2||Thermal Shock||300 Cycles||
H: +100℃ 5min ∫ 10 sec
L: -10℃ 5min
|3||Temperature Cycle||300 Cycles||
H: +100℃ 15min ∫ 5min
L: -40℃ 15min
|4||High Temperature Storage||1000Hrs.||Temp: 100℃||25pcs||0/1|
|5||DC Operating Life||1000Hrs.||IF=150mA||25pcs||0/1|
|6||Low Temperature Storage||1000Hrs.||Temp: -40℃||25pcs||0/1|
|7||High Temperature/ High Humidity||1000Hrs.||85℃/85%RH||25pcs||0/1|
2) Criteria for Judging the Damage:
|Item||Symbol||Test Conditions||Criteria for Judgment|
*) F.V.: First Value.
Carrier Tape Dimensions:
Loaded quantity 4000 PCS per reel.
Please read the following notes before using the product:
Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen).
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture adsorbent material (silica gel) has fabled away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment: 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile.
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
6. Caution in ESD
Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded.
Contact Person: Tanky