Payment & Shipping Terms:
|Product Name:||1W High Power With Lens Full Color LED||Package:||High Power With Lens|
|Emitted Color:||RGB Full Color||Peak Emission Wavelength:||Hyper Red:620-630nm,Pure Green:525-530nm,Blue:460-470nm|
|Lens Type:||Water Clear||Forward Voltage @20ma:||Hyper Red:2.0-3.0V,Pure Green:2.8-4.0V,Blue:2.8-4.0|
|Luminous Intensity:||Hyper Red:40LM,Pure Green:50LM,Blue:10LM||Viewing Angle:||120Deg|
multi color led diode,
green light emitting diode
1W High Power Light Emitting Diode with Lens , Full Color LED Water Clear Lens Type
This is our 1W High Power with Lens Full Color LED, Water Clear Lens and the Emitting Color of this size is RGB full Color.
1.Up-lighters and Down-lighters.
|Part No.||Chip Material||Source Color|
Absolute Maximum Ratings at Ta=25℃
Peak Pulse Current
(tp≤100μs, Duty cycle=0.25)
|LED Junction Temperature||Tj||135||℃|
|Operating Temperature Range||Topr||-40 to +80||℃|
|Storage Temperature Range||Tstg||-40 to +100||℃|
|Soldering Time at 260 ℃ (Max.)||Tsol||5||Seconds|
1. Proper current derating must be observed to maintain junction temperature below the maximum.
2. LEDs are not designed to be driven in reserve bias.
Electrical Optical Characteristics at Ta=25℃
|Parameters||Symbol||Emitting Color||Min.||Typ.||Max.||Unit||Test Condition|
|Viewing Angle||2θ1/2||Full color||---||120||---||Deg||IF=350mA|
|Peak Emission Wavelength||λp||Red||---||625||---||nm||
|Spectral Line Half-Width||△λ||Red||---||18||---||nm||IF=350mA|
1. Luminous Flux Measurement allowance is ± 10%.
2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
Typical Electrical-Optical Characteristics Curves
(25℃ Ambient Temperature Unless Otherwise Noted)
Typical Electrical / Optical Characteristics Curves
Precautions For Use:
Though HP60M has conducted ESD protection mechanism, customer must not use the device in reverse and should apply resistors for extra protection. Otherwise slight voltage shift may cause enormou current change and burn out failure would happen.
① Do not open moisture proof bag before the products are ready to use.
② Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
③ The LEDs should be used within a year.
④ After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
⑤ The LEDs should be used within 168 hours (7 days) after opening the package.
⑥ If the moisture absorbent material (silicone gel) has faded away or the LEDs have exceeded the storag time, baking treatment should be performed using the following conditions.
⑦ Pre-curing treatment: 60±5℃ for 24 hours.
3. Thermal Management
① Because HP60M LED is a high power dissipation device, special and sufficient consideration in thermal management design must be made to optimize the thermal performance.
② Heat sink design is implemented in the device for an additional thermal connection. Since the device is capable of SMT process, tin must be spread both heat sink and solder pads areas to dissipate the heat.
③ A high thermal conductivity substrate, such as Aluminum or Copper plate etc, must be applied for external thermal management. It is strongly recommended that the outer heat sink or PCB dimension per LED can not be less than 25 x 25 x 1 (L x W x H) mm. The materials for outer heat sink can be FR4 on Aluminum, MCPCB, or FPC on Aluminum.
④ Special thermal designs are also recommended to take in outer heat sink design, such as FR4 PCB on Aluminum with thermal vias or FPC on Aluminum with thermal conductive adhesive, etc.
⑤ Sufficient thermal management must be conducted, or the die junction temperature will be over the limit under large electronic driving and LED lifetime will decrease critically.
4. Soldering Condition
① Soldering should not be done more than two times.
② While soldering, do not put stress on the LEDs during heating.
③ After soldering, do not warp the circuit board.
5. Soldering Iron
① For prototype builds or small series production runs it is possible to place and solder the LED by hand.
② Dispensing thermal conductive glue or grease on the substrates and follow its curing spec. Press LED housing to closely connect LED and substrate.
③ It is recommended to hand solder the leads with a solder tip temperature of 280°C for less than 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal.
④ Be careful because the damage of the product is often started at the time of the hand solder.
6. Handling Indications
During processing, mechanical stress on the surface should be minimized as much as possible.
Sharp objects of all types should not be used to pierce the sealing compound.
Contact Person: Tanky